Pioneer SC-09TX - Elite AV Network Receiver, Operating Instructions Manual

Page: 110 / 160

Using other functions
12
110
En
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if
ANALOG
INPUT OVER is displayed on the LCD or if you can hear
distortion in the sound.
1
• Set the operation selector switch to RCV, then press
A.ATT to switch the input attenuator on or off.
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
• Set the operation selector switch to RCV, then press
SLEEP repeatedly to set the sleep time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
2
Switching the contents displayed on
the LCD
One of three patterns of information to be displayed on
the LCD can be selected. By default this is set to ‘OSD’.
• Press LCD VIEW on the front panel to change the
pattern of information.
3
This can be set separately for different inputs. Note,
however, that only inputs with a video terminal (DVD/LD,
BD, TV, SAT, DVR/VCR1, DVR/VCR2, VIDEO/GAME1 and
VIDEO/GAME2), inputs from an iPod on which video is
playing and inputs from MULTI CH IN for which VIDEO
INPUT is set to something other than
OFF can be set.
With HDMI inputs, it is not possible to display external
images on the LCD screen. To do so, connect to this
receiver’s video input using an analog video cable.
Dimming the display
You can choose between four brightness levels for the
front LCD display. Note that when selecting sources, the
display automatically brightens for a few seconds.
• Set the operation selector switch to RCV, then press
DIMMER repeatedly to change the brightness of the
front LCD display.
Switching the HDMI output
Set which terminal to use when outputting video and
audio signals from the HDMI output terminals (HDMI
OUT1 or HDMI OUT2).
The HDMI OUT1 terminal is compatible with the HDMI
control function.
• Set the operation selector switch to RCV, then press
HDMI OUT.
Please wait a while when Please wait ... is displayed. No
operations other than switching the power between
standby or on can be performed at this time.
The output switches between HDMI OUT1 and HDMI
OUT2 each time the button is pressed.
4
Note
1 The attenuator isn’t available with digital sources, or when using the Stream Direct modes.
2 You can also switch off the sleep timer simply by switching off the receiver.
3 Depending on the settings of the video adjustment function (page 108), the external image may not appear on the LCD.
SOURCE
TV RCV
VOL
VOL CH
SOURCE
TV RCV
iPod CTRL
SR+
CLR
SBch PHASE
A.ATT GENRE HDMI OUT
D.ACCESS
ENTER
MCACC CLASS
DISP
CH
A.ATT
SOURCE
TV RCV
VOL
VOL CH
SOURCE
TV RCV
SIGNAL SEL SLEEP AUDIO
iPod CTRL
DIMMER
SR+ SBch PHASE
A ATT GENRE HDMI OUT
DISP
SLEEP
30 min
60 min
90 min Off
OSD
External
Image &
OSD
External
Image
Only
4 • Synchronized amp mode on page 99 is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI
OUT1, then select the synchronized amp mode using the plasma TV’s remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI6.
SOURCE
TV RCV
VOL
VOL CH
SOURCE
TV RCV
SIGNAL SEL SLEEP AUDIO
iPod CTRL
DIMMER
SR+ SBch PHASE
DISP
DIMMER
SC_09TX.book Page 110 Monday, November 26, 2007 10:32 PM