Additional information
14
125
En
Settings
Professional Calibration EQ graphical output
Display
Symptom
Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also
Problems when using the Auto MCACC Setup
on page 14). If the noise level cannot be kept low enough, you
will have to set up the surround sound manually (page 56).
After using the Auto MCACC
Setup, the speaker size setting is
incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch off
all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.
Change the speaker setting manually in
Speaker Setting
on page 56, and use the
ALL (Keep SP System)
option for the
Custom Menu
in
Automatic MCACC (Expert)
on page 44 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 49)
properly.
• Check that the speakers are all in phase (make sure the positive (
+
) and negative (
–
) terminals are
matched up properly).
The display shows
KEY LOCK
ON
when you try to make
settings.
• With the receiver in standby, press
STANDBY/ON
while holding down the
SPEAKERS
button to
disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
Symptom
Remedy
The EQ response displayed in the
graphical output following
calibration does not appear
entirely flat.
• There are cases where the graph does not appear flat (even when selecting
ALL CH ADJUST
in the Auto
MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.
• Areas of the graph may appear identical (before and after) when there is little or no adjustment needed.
• The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using the
Manual MCACC setup
on
page 48 do not appear to change
the graphical output.
• Despite level adjustments being made, the filters used for analysis may not display these adjustments in
the graphical output. However, these adjustments are taken this into account by the filters dedicated to
overall system calibration.
Lower frequency response
curves do not seem to have been
calibrated for
SMALL
speakers.
• Low frequencies used in bass management (the subwoofer channel) will not change for speakers that
have been specified as
SMALL
in the configuration, or do not output these frequencies.
• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable sound is
output for display.
Graphical output data seems to
have disappeared.
• If the power is switched off, the measurement data for graphical output to a PC is cleared.
Symptom
Remedy
The display is dark or off.
• Press
DIMMER
repeatedly to select a different brightness.
After making an adjustment the
display goes off.
• Press
DIMMER
repeatedly to select a different brightness.
You can’t get
DIGITAL
to display
when using the
SIGNAL SEL
button.
• Check the digital connections and make sure that the digital inputs are assigned correctly (see
The Input
Setup menu
on page 101).
• If the multichannel analog inputs are selected, select a different input source.
DOLBY DIGITAL or DTS does not
appear on the STATUS audio
input information screen when
playing Dolby/DTS software.
• DOLBY DIGITAL or DTS does not appear if playback is paused.
• Check the playback (especially the digital output) settings of the source component.
When playing a DVD-Audio disc,
the DVD player display shows
96 kHz
. However, the receiver’s
display does not.
• This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of
the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.
During playback of a DTS 96/24
source, the display doesn’t show
96 kHz
.
• Make sure that the receiver is set to
AUTO
or
DIGITAL
(see
Choosing the input signal
on page 39).
SC_09TX.book Page 125 Monday, November 26, 2007 10:32 PM
Summary of Contents for SC-09TX - Elite AV Network Receiver
Page 1: ...uctions REC ...
Page 160: ......
