Pioneer PDA-4002 Technical Manual Download Page 92

Page: 92 / 163

2. The display mounting is complete. Now set the optimal angle.

Wall side

Mounting standard metal fixtures (PDK-4006)

3. After securing the fixture with screws, open it as shown in the figure and tighten the screws

on the left and

right sides of the vertical frame.

5) Mounting the plasma display

1. As shown below, two workers should hold the left and right ends of the plasma display and insert four monitor

fixing bolts into the mounting fixture holes. First insert the bolts in the bottom holes, then in the top holes.

Insert a monitor fixing
bolt into the hole of the
mounting fixture and
set it down.

Tighten the screw from
above to prevent the bolt
from falling out.

Display

Tighten the nut.

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands