Pioneer PDA-4002 Technical Manual Download Page 61

Page: 61 / 163

6 1

3.4.14 Vertical connections

This machine is designed to be used vertical connection, but some operations under vertical connection may adversely

affect ventilation in the machine. Therefore, observe the following conditions for safe operation:

Installation of up to three units (Vertical connection)

The following table lists the operating temperature conditions. Use the units under conditions that keep the

outside atmosphere in this range.

Special installation (Vertical connections)

Wall

<Reference> Air flow rate of the fan per unit: 2 m

/min or more

* For the securing method, see 3.4 Special installations and 3.4.2 Wall hanging.

* The same conditions apply to the working temperature requirements for a speaker system (PDP-S03-LR).

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

Clearance A to the wall

VIDEO

Machintosh (66.7Hz)

VGA (60HZ)

VGA (72.8Hz, 75Hz)

50 mm or more

0~35

Partition

Make sure to
mount them
so that they
will not block
any exhaust
holes.

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands