Pioneer PDA-4002 Technical Manual Download Page 153

Page: 153 / 163

153

5.3.2 Precautions

• Input cannot be switched over in Menu or Integrator modes.

First select the input to adjust, then move to Menu mode or Integrator mode.

• The system automatically exits Menu mode or Integrator mode if one of the following occurs:

a) The main switch is turned off (AC OFF).

b) STANDBY status is invoked.

c) A non-operational period persists for approx. 180 seconds.

d) The KEY-LOCK button of the main body is pressed.

e) Input signals are externally switched-over, or a no-signal state arises.

f ) The system is switched to RS-232C adjustment mode with an <AJY> command.

g) The protective circuit (P.D.) is activated.

Note: For a) and g), only the item currently being adjusted is not placed in latest data in the memory.

Integrator mode

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands