Pioneer PDA-4002 Technical Manual Download Page 111

Page: 111 / 163

111

Mounting standard metal fixtures (PDM-4001)

5. Tighten the nuts to secure the monitor.

Insert a monitor securing bolt into a

potbellied hole on the slide frame,

and lower the bolt.

Plasma display

Tighten the nut.

6. Mounting a chain to release the locking fitting.

The multiple installation fixture is so designed that the plasma display can be drawn forward for easy maintenance by

releasing the locking fittings. Attaching a chain to the locking fitting allows to easily release the locking mechanism

from the lowermost area.

For multiple installation, tags in three different colors (red, blue and yellow) are provided so that they can easily

differentiate each column or each unit from the others. It is, therefore, recommended that those tags are attached to

the chains.

7. Sliding prevention mechanism

A sliding prevention mechanism is provided to prevent any accident so that the plasma display will not inattentively

slide out when the multiple installation fixtures are mounted forward tilted or downward tilted.

• If you use those two nuts and two bolts that were removed when making preparations for installation as shown

below, it is possible to prevent sliding.

Place the nuts.

Hook

Chain

919 (Outer size of metal fixture)

Remove the bolts (both left

and right bolts)

717 (Outer size of metal fixture)

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands