Pioneer PDA-4002 Technical Manual Download Page 130

Page: 130 / 163

130

Fig. 4

Mounting standard metal fixtures
(Precautions for installing the optional speaker)

Monitor mounting bolt
(supplied with the PDK-4006)

Hole rivet

Monitor fixing bolt
(supplied with the PDK-4006)

Fig. 5

3) Wall-hanging metal fixture (PDK-4006)

When the wall hanging metal fixture is mounted to the plasma display with the optional speaker, use the monitor-

mounting bolt to tighten the speaker, as indicated in Fig.4. Next, as shown in Fig.5, follow the usual steps for mounting

the wall hanging metal fixture.

After the optional speaker is mounted, it will be difficult to see the monitor-mounting bolt attaching section on the wall

hanging metal fixture side and the angle setting screw section. Take appropriate precautions when mounting the

optional speaker.

Monitor fixing bolt
(supplied with the PDK-4006)

Wall hanging metal fixture

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands