Pioneer PDA-4002 Technical Manual Download Page 58

Page: 58 / 163

5 8

Special installation (Installation under the floor (using the PDM-4001))

3.4.12 Installation under the floor (using the PDM-4001)

• If protective glass or similar material is used, the multi-installation fixture (PDM-4001) shown in the following figure is

very useful.

600 mm or more

Intake

Exhaust

Protective glass surface

Looking in the direction of the arrow (see the next page)

If the display is used in the closed space, observe the following conditions in the above environment:

≥

20 mm (clearance between the protective glass and PDP)

≥

100 mm (clearance between the PDP and side wall)

≥

50 mm (clearance between the PDP and side wall)

A + 50 mm
or less

60 mm
or less

Exhaust fan

Flow of air from the air conditioner

Intake port

Tempered glass, etc. (permeable)

Multi-installation fixture (PDM-4001)

291mm

A + 50 mm
or less

60 mm or
less

Exhaust port

600 mm or more

Floor

Exhaust

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

VIDEO

Machintosh (66.7Hz)

VGA (60Hz)

VGA (72.8Hz, 75Hz)

Without exhaust fan

0~30

Not usable

With exhaust fan

0~35

50mm

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands