Pioneer PDA-4002 Technical Manual Download Page 73

Page: 73 / 163

The figure illustrates the one-sided PDK-4002 fixture.

The PDK-4003, which is double-sided, is assembled and installed in the same manner.

Mounting standard metal fixtures (PDK-4002)

Pattern paper

Ceiling flange

COMP

Flat washer

[WC100FZK]

Spring washer

[WS100FZK]

Hexagonal socket head

bolt (M10

85)

[SME100H850FZK]

Hexagonal socket head

bolt (M8

75)

[SME80H750FZK]

Spring washer

[WS80FZK]

Flat washer

[WC80FZK]

Hexagonal socket head

bolt (to eliminate

backlash) (M6

10)

[SME60H100FZK]

Monitor frame

Cable holes

Spacer

Support COMP

Center rod

Monitor bracket

Hole cover

Use this hole cover to hide

the machined hole in the

suspended ceiling.

Hexagonal socket head

bolt (to eliminate black

lash) (M5

16)

[SME50H160FZK]

Hexagonal socket head
bolt (for tilt adjustment)
(M6

10)

[SME60H100FZK]

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands