Pioneer PDA-4002 Technical Manual Download Page 60

Page: 60 / 163

6 0

3.4.13 Horizontal connections

While the display is designed to accommodate side-by-side installations, keep in mind that specific installation

configurations may affect ventilation. Observe the following requirements:

Installation of up to three units (Horizontal connection)

The following table lists the operating temperature conditions. Use the units under conditions that keep the

outside atmosphere in this range.

Special installation (Horizontal connections)

Partition

Unit A

Unit B

Unit C

* The same conditions apply to the working temperature requirements for a speaker system (PDP-S03-LR).

* For the securing method, see 3.4 Special installations and 3.4.2 Wall hanging.

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

Clearance A to the wall

VIDEO

Machintosh (66.7Hz)

VGA (60HZ)

VGA (72.8Hz, 75Hz)

≥

50 mm

0~35

In case of lateral connections, ensure that left and right partitions are provided.

Be careful to install the partitions so that the air on the left and right backside of the set is not

mixed up.

Summary of Contents for PDA-4002




































































































































































Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands

Pioneer PDA-4002, Technical Manual

Search results

Summary of Contents for PDA-4002

Reviews:

Related manuals for PDA-4002

Brands by name

Popular brands