Pioneer ELITE VSX-LX304 Instruction Manual Download Page 11

Page: 11 / 180

≫

≫

≫

≫

≫

≫

INPUT SELECTOR dial: Switch the input to be played.

FL OFF indicator: Lights up when the display is turned off by repeatedly

pressing the DIMMER button on the remote controller.

3. ZONE 2 ON/OFF button: Turns ZONE 2 ON/OFF. (

p94

)

4. ZONE 3 ON/OFF button: Turns ZONE 3 ON/OFF. (

p96

)

ZONE CONTROL button: Controls the multi-zone function. (

p93

)

6. HOME MENU button: Displays the Home. (

p122, 147, 152

)

Display (

p12

)

Cursor buttons ( / / / )

and ENTER button: Select the item with the

cursors and press ENTER to confirm. Use them to tune to stations when using

TUNER. (

p88

)

NETWORK indicator: This lights when "NET" is selected with the input

selector and the unit is connected to the network. Lights up when any of the

following functions is working or enabled in standby state of this unit. When

this indicator is lighting, the power consumption in standby state increases,

however, the increase in power consumption is minimized by entering the

HYBRID STANDBY mode where only the essential circuits operate. It does not

light when ZONE 2/ZONE 3 is on, however.

–

HDMI CEC (

p136

)

–

HDMI Standby Through (

p136

)

–

USB Power Out at Standby (

p138

)

–

Network Standby (

p138

)

–

Bluetooth Wakeup (

p138

)

10.

MCACC indicator: This lights when you have enabled the speaker calibration

made with MCACC. (

p148, 160

)

11.

Remote control sensor: Receives signals from the remote controller.

•

The signal range of the remote controller is within about 16´/5 m, at an

angle of 20° on the perpendicular axis and 30° to either side.

12.

RETURN button: Returns the display to the previous state.

13. MASTER VOLUME

14.

STANDBY/ON button

15.

PHONES jack: Headphones with a standard plug (ø1/4"/6.3 mm) are

connected.

16.

SETUP MIC jack: The supplied speaker setup microphone is connected.

(

p148, 160

)

17. TUNER button: Switches the input to be played to "TUNER". Also, pressing

this button repeatedly switches the input between "AM" and "FM".

18.

PERSONAL PRESET 1/2/3 buttons: Registers the current setting conditions

such as input selector, listening mode, etc. or call the registered settings.

(

p98

)

19.

Listening mode button: Switches the listening mode. (

p103

)

20.

USB port: A USB storage device is connected so that music files stored in it

can be played. Supply of power to USB devices while in the standby mode is

not supported. (

p75

)

21.

AUX INPUT AUDIO/HDMI jack: Connect a video camera, etc. using a stereo

mini plug cable (ø1/8″/3.5 mm) or HDMI cable.

(

p56

)

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands