Pioneer ELITE VSX-LX304 Instruction Manual Download Page 152

Page: 152 / 180

152

≫

≫

≫

≫

≫

≫

Network/Bluetooth

Menu operations

Make settings related to network connections and BLUETOOTH.

Use the on-screen displays (OSD) that appear on the TV to make the settings.

Press

on the remote controller to display the Home screen, select Network/

Bluetooth with the cursors on the remote controller, then press ENTER.

Select the item with the cursor

/ / / buttons of the remote controller and

press ENTER to confirm your selection.

Use the cursors /

to change the default values.

•

To return to the previous screen, press

• To exit the settings, press .

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands