Pioneer ELITE VSX-LX304 Instruction Manual Download Page 96

Page: 96 / 180

≫

≫

≫

≫

≫

≫

Playing Back (ZONE 3)

In the remote controller operation, while pressing and holding the ZONE 3 SHIFT

button on the remote controller, operate with each button. Settings are required to

playback a source in ZONE 3.

Set "Speaker" - "Configuration" - "Zone Speaker" in the System Setup menu

(

p96

) to "Zone 2/Zone 3".

Point the remote controller at the unit, and while pressing and holding the

ZONE 3 SHIFT button on the remote controller, press

• "Z3" on the display of the main unit lights up.

While pressing and holding the ZONE 3 SHIFT button on the remote controller,

press the input selector of the input source you want to play in the separate

room. When operating on the main unit, press the ZONE CONTROL button

repeatedly to select "Z3" on the display, then within 8 seconds select the input

you want to play in another room using the input selector dial.

To adjust the volume of the ZONE speakers in the separate room, press

the volume buttons while pressing the ZONE 3 SHIFT button on the remote

controller. When operating on the main unit, press the ZONE CONTROL

button repeatedly to select "Z3" on the display, then within 8 seconds adjust

using the MASTER VOLUME knob.

•

If you turn the unit to standby during multi-zone playback, the Z3 indicator is

dimmed, and the playback mode is switched to playback in a separate room

only. Setting ZONE 3 to on while the unit is in standby also switches the

playback mode to playback in a separate room only.

• For ZONE 3 output, audio from externally connected AV components can be

output only when it is an analog audio signal.

•

DSD audio signals cannot be output to ZONE 3 when selected with the "NET"

or "USB" input selector.

•

If ZONE 3 is on, power consumption during standby will increase.

To set the function to off:

While pressing and holding ZONE 3 SHIFT button,

press

. Alternatively, press the ZONE 3 ON/OFF button on the main unit.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands