Pioneer ELITE VSX-LX304 Instruction Manual Download Page 88

Page: 88 / 180

≫

≫

≫

≫

≫

≫

Listening To the AM/FM Radio

You can receive AM and FM radio stations on this unit with the built-in tuner.

Tuning into a Radio Station

Perform the following procedure when this unit is on.

Tuning Automatically

1. Press TUNER repeatedly to select either "AM" or "FM".

2. Press MODE repeatedly to display "TunMode: Auto" on the display.

3. When you press the cursors / , automatic tuning starts, and searching

stops when a station is found. When tuned in to a radio station, the "TUNED"

indicator on the display lights up. When tuned in to an FM radio station, the

"STEREO" indicator lights up.

MODE

/ / /

ENTER

TUNER

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands