Pioneer ELITE VSX-LX304 Instruction Manual Download Page 14

Page: 14 / 180

≫

≫

≫

≫

≫

≫

1. DIGITAL AUDIO IN OPTICAL/COAXIAL jacks: Input TV or AV component

digital audio signals with a digital optical cable or digital coaxial cable.

ANTENNA AM LOOP/FM UNBAL 75 Ω terminal: The supplied antennas are

connected.

Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH

enabled device. Adjust their angles according to the connection status.

HDMI OUT jacks: Transmit video signals and audio signals with an HDMI

cable connected to a monitor such as a TV or projector.

RS-232C port: Connect a home control system equipped with an RS-232C

port. For adopting a home control system, contact the specialized stores.

6. HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable

connected to an AV component.

7. NETWORK port: Connect to the network with a LAN cable.

8. USB port: A USB storage device is connected so that music files stored in

it can be played. (

p75

) You can also supply power (5 V/1 A) to USB

devices with a USB cable.

AC IN: The supplied power cord is connected.

10.

SIGNAL GND terminal: The ground wire of the turntable is connected.

11.

AUDIO IN jacks: Input AV component audio signal with an analog audio cable.

12.

IR IN/OUT port: Connect a remote control receiver unit. (

p62

)

13.

12V TRIGGER OUT A/B jack: Connect a device equipped with a 12V trigger

input jack to enable power link operation between the device and this unit.

(

p63

)

14.

SPEAKERS terminals: Connect speakers with speaker cables. (North

American models support banana plugs. Use a plug 4 mm in diameter. Y plug

connection is not supported.)

15.

SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a

subwoofer cable. Up to two powered subwoofers can be connected. The same

signal is output from each of the SUBWOOFER PRE OUT jacks.

16. ZONE 2 PRE/LINE OUT jacks: Output audio signals with an analog audio

cable connected to a pre-main amplifier or a power amplifier in a separate

room (ZONE 2).

ZONE B LINE OUT jacks: Connect to a pre-main amplifier with an analog

audio cable, and simultaneously output audio of the same source as that of

the speakers (ZONE A) connected to this unit.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands