Pioneer ELITE VSX-LX304 Instruction Manual Download Page 173

Page: 173 / 180

173

≫

≫

≫

≫

≫

≫

❏

The measurement results of Full Auto MCACC show different distances to the speakers from the

actual ones

• Depending on the speakers you are using, some errors may occur in the measurement results. If this is the case, make the settings in "System

Setup" - "Speaker" - "Distance".

(

p130

)

❏

The measurement results of Full Auto MCACC show that the volume level of the subwoofer has been

corrected to the lower limit

•

The volume level correction of the subwoofer may not have been completed. Lower the volume of the subwoofer before Full Auto MCACC

measurement.

❏

Midnight function does not work

•

Make sure the source material is Dolby Digital, Dolby Digital Plus, Dolby TrueHD or DTS.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands