Pioneer ELITE VSX-LX304 Instruction Manual Download Page 37 | Manualshive

Page: 37 / 180

background image

37

≫

≫

≫

Connections

≫

≫

≫

Speaker Connections and "Speaker Setup" Settings

Connections

(Note) Speaker Impedance

Connect speakers with an impedance of 4 Ω to 16 Ω. If any of the speakers to be connected has an impedance of 4 Ω or more and less than 6 Ω, set "Speaker

Impedance" to "4ohms" for "Speaker Setup" in the Initial Setup section (

p159

). When setting "Speaker Impedance" from the System Setup menu, press the

button on the remote controller to display the Home screen, and select "System Setup" - "Speaker" - "Configuration", then set "Speaker Impedance" (

p128

) to

"4ohms".

Connect the Speaker Cables

1/2˝

(12 mm)

Make correct connection between the unit's jacks and speaker's jacks (+ side to + side, and - side to - side) for each channel. If the connection is wrong, a bass sound

will not be reproduced properly due to reverse phase. Twist the wires exposed from the tip of the speaker cable so that the wires do not stick out of the speaker terminal

when connecting. If the exposed wires touch the rear panel, or the + side and - side wires touch each other, a malfunction may occur.

«
...
35
36
37
38
39
...
»

Summary of Contents for ELITE VSX-LX304





















































































































































































Reviews:

No comments

Related manuals for ELITE VSX-LX304

Brand: Yaesu Pages: 40

Brand: Yaesu Pages: 35

Brand: Yaesu Pages: 39

Brand: Yaesu Pages: 2

Brand: Yaesu Pages: 15

TRIPP LITE Series

Brand: Eaton Pages: 16

Brand: DMP Electronics Pages: 4

Brand: Barlow Wadley Pages: 11

Brand: Zenith Pages: 70

Brand: Arris Pages: 24

Brand: Albrecht Pages: 16

Brand: Intelix Pages: 8

Brand: Zamel Pages: 21

Brand: VDO Pages: 2

Brand: Triax Pages: 30

Brand: Alpine Pages: 82

Brand: A-Neuvideo Pages: 11

Brand: Trillium Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands