Pioneer ELITE VSX-LX304 Instruction Manual Download Page 153

Page: 153 / 180

153

≫

≫

≫

≫

≫

≫

Network

•

When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the

setting automatically. ("Enable" is set by default.) To assign fixed IP addresses

to each components, you must set "DHCP" to "Disable" and assign an address

to this unit in "IP Address" as well as set information related to your LAN, such

as Subnet Mask and Gateway.

Setting Item

Default Value

Setting Details

Wi-Fi

Off(Wired)

Connect the unit to network via wireless LAN

router.

"On": Wireless LAN connection

"Off (Wired)": Wired LAN connection

•

When switching between "On" and "Off(Wired)",

stop the Network service. Also, when group

playback is in process, cancel the group

playback once, and then switch the setting.

Wi-Fi Setup

You can configure wireless LAN settings by

pressing ENTER when "Start" is displayed.

Wi-Fi Status

The information of the connected access point will

be displayed.

"SSID": SSID of the connected access point.

"Signal": Signal strength of the connected access

point.

"Status": Status of the connected access point.

MAC Address

This is the MAC address of this unit.

This value is specific to the component and cannot

be changed.

DHCP

Enable

"Enable": Auto configuration by DHCP

"Disable": Manual configuration without DHCP

• If selecting "Disable", you must set "IP Address",

"Subnet Mask", "Gateway", and "DNS Server"

manually.

IP Address

0.0.0.0

Displays/Sets the IP address.

Subnet Mask

0.0.0.0

Displays/Sets the subnet mask.

Gateway

0.0.0.0

Displays/Sets the gateway.

DNS Server

0.0.0.0

Displays/Sets the primary DNS server.

Setting Item

Default Value

Setting Details

Proxy URL

Displays/Sets the proxy server URL.

Proxy Port

8080

Displays/Sets the proxy server port number when

you enter "Proxy URL".

Friendly Name

Pioneer VSX-

LX304 XXXXXX

Change the device name for this unit which is

shown on other devices connected to the network

to an easily recognized name.

1. Press ENTER to display the Edit screen.

2. Select a character or symbol with the cursors

and press ENTER.

Repeat it to input 31 or less characters.

"A/a": Switches between upper and lower cases.

(Pressing MODE on the remote controller also

toggles between upper and lower cases.)

"←" "→": Moves the cursor to the arrow

direction.

": Removes a character on the left of the

cursor.

" ": Enters a space.

•

Pressing CLEAR on the remote controller will

remove all the input characters.

3. After inputting, select "OK" with the cursors and

press ENTER.

The input name will be saved.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands