Pioneer ELITE VSX-LX304 Instruction Manual Download Page 98

Page: 98 / 180

≫

≫

≫

≫

≫

≫

Convenience functions

Using PERSONAL PRESET

Registration

You can register settings (

p99

) such as the current input selector and

listening mode with the three PERSONAL PRESET buttons, and call a registered

setting in a single operation.

e.g.) Pressing the PERSONAL PRESET button will automatically switch the input

selector to "TUNER" to receive the registered station. Also, the listening mode

and volume level are switched as registered.
Perform the following steps in the state of the setting to register.

1. Press and hold any of the 1 to 3 buttons of PERSONAL PRESET.

2. "Preset Written" appears on the display, and the setting is registered. If

registration has already been made, the registered setting is overwritten.

PERSONAL

PRESET

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands