Physio Control 3206720-All Manual Download Page 9

Page: 9 / 33

Title

LIFEPAK 15 Monitor Defibrillator CO2 Upgrade

Page

9 of 33

Doc Type

Service Process Document

Doc ID

3308217

Doc Rev

Doc State

Released

State Date

09/08/2011

Removing the System (A01)/Therapy (A04) PCB
Assembly

5.1

Disconnect the connectors on the system PCB
as follows:

5.1.1 J1 - Press the connector locking tabs and

disconnect the power/system PCB cable
(W01).

5.1.2 (The system/interface PCB cable was

disconnected during case disassembly).

5.1.3 J4 - Disconnect the USB flex connector

(W14).

5.1.4 J6

– Disconnect the ECG connector cable

(W7).

5.1.5 J7 - Disconnect the IP/Temp connector cable

of the IP/Temp wire harness (W33 or W35) (if
present).

5.1.6 J106 (on A22 biphasic module) - Disconnect

the biphasic to therapy cable from the
biphasic PCB (W20).

Disconnect J4

USB Flex

Connector (W14)

Disconnect J6 ECG

and J7 IP/ Temp (if

present) connectors.

(W7 & W33)

Disconnect J1

PWR/ SYS Cable

(W01)

Disconnect J106

BTE cable

connector (W20)

Summary of Contents for 3206720-All


































Search results

Summary of Contents for 3206720-All

Reviews:

Related manuals for 3206720-All

Brands by name

Popular brands

Physio Control 3206720-All, Manual

Search results

Summary of Contents for 3206720-All

Reviews:

Related manuals for 3206720-All

Brands by name

Popular brands