Physio Control 3206720-All Manual Download Page 23 | Manualshive

Page: 23 / 33

background image

Title

LIFEPAK 15 Monitor Defibrillator CO2 Upgrade

Page

23 of 33

Doc Type

Service Process Document

Doc ID

3308217

Doc Rev

A

Doc State

Released

State Date

09/08/2011

13. Installing the OEM PCB (A06) (continued)

13.8 Connect the power/contact cable (W05) to the

power PCB J12.

13.9 Connect the power/system cable (W01) to the

power PCB J17.

NOTE:

The W01 - power/system PCB cable is

under the OEM shield.

13.10 Install the OEM shield (3208298-000).

13.11 Connect the W02 - power/therapy PCB cable

(3009726) to J8 on the power PCB.

13.12 Route the left side of the OEM shield under the

power/therapy cable J8 connector and over the
top of J11, J13 and J15 connectors on power
PCB.

PWR/Therapy

Cable

3009726-05 (W02)

OEM Shield

3208298

Power/System

Cable 3207692

(W01)

Power/Contact

Cable 3207692

(W05)

Route CO2 Wire

Harness As

Shown

«
...
21
22
23
24
25
...
»

Summary of Contents for 3206720-All


































Reviews:

No comments

Related manuals for 3206720-All

Brand: Labnet Pages: 2

Brand: Modulate Pages: 2

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

MiniLift160 Classic

Brand: Handicare Pages: 28

Brand: Hands Free Farm Pages: 24

Brand: i-Optik Pages: 75

GED5000IL Series

Brand: Zimmer Pages: 52

Brand: Megger Pages: 12

Brand: Tecsis Pages: 52

Brand: GGM gastro Pages: 3

Brand: Wartmann Pages: 56

Brand: Fri-Jado Pages: 48

Brand: Janschitz Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands