manualshive.com logo in svg

Photon Focus CameraLink MV1-D1312 series, User Manual

Share
Download
Photon Focus CameraLink MV1-D1312 series User Manual Download Page 50

4 Functionality

4.4

Trigger and Strobe

4.4.1

Introduction

The start of the exposure of the camera’s image sensor is controlled by the trigger. The trigger
can either be generated internally by the camera (free running trigger mode) or by an external
device (external trigger mode).
This section refers to the external trigger mode if not otherwise specified.
In external trigger mode, the trigger can be applied through the CameraLink

®

interface

(interface trigger) or directly by the power supply connector of the camera (I/O Trigger) (see
Section 4.4.2). The trigger signal can be configured to be active high or active low. When the
frequency of the incoming triggers is higher than the maximal frame rate of the current
camera settings, then some trigger pulses will be missed. A missed trigger counter counts these
events. This counter can be read out by the user.
The exposure time in external trigger mode can be defined by the setting of the exposure time
register (camera controlled exposure mode) or by the width of the incoming trigger pulse
(trigger controlled exposure mode) (see Section 4.4.3).
An external trigger pulse starts the exposure of one image. In Burst Trigger Mode however, a
trigger pulse starts the exposure of a user defined number of images (see Section 4.4.5).
The start of the exposure is shortly after the active edge of the incoming trigger. An additional
trigger delay can be applied that delays the start of the exposure by a user defined time (see
Section 4.4.4). This often used to start the exposure after the trigger to a flash lighting source.

4.4.2

Trigger Source

The trigger signal can be configured to be active high or active low. One of the following
trigger sources can be used:

Free running

The trigger is generated internally by the camera. Exposure starts immediately

after the camera is ready and the maximal possible frame rate is attained, if Constant
Frame Rate mode is disabled. In Constant Frame Rate mode, exposure starts after a
user-specified time (Frame Time) has elapsed from the previous exposure start and
therefore the frame rate is set to a user defined value.

Interface Trigger

In the interface trigger mode, the trigger signal is applied to the camera by

the CameraLink

®

interface. Fig. 4.31 shows a diagram of the interface trigger setup. The

trigger is generated by the frame grabber board and sent on the CC1 signal through the
CameraLink

®

interface. Some frame grabbers allow the connection external trigger

devices through an I/O card. A schematic diagram of this setup is shown in Fig. 4.32.

I/O Trigger

In the I/O trigger mode, the trigger signal is applied directly to the camera by the

power supply connector (via an optocoupler). A setup of this mode is shown in Fig. 4.33.
The electrical interface of the I/O trigger input and the strobe output is described in
Section 5.1.3.

4.4.3

Exposure Time Control

Depending on the trigger mode, the exposure time can be determined either by the camera or
by the trigger signal itself:

Camera-controlled Exposure time

In this trigger mode the exposure time is defined by the

camera. For an active high trigger signal, the camera starts the exposure with a positive
trigger edge and stops it when the preprogrammed exposure time has elapsed. The
exposure time is defined by the software.

48

Summary of Contents for CameraLink MV1-D1312 series
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands