Phoenix Contact IOL MA8 PN DI8 User Manual Download

Page: 75 / 84

Troubleshooting

4022_en_A

PHOENIX CONTACT

C/Q

Off

SIO mode - signal is low or disabled

Solid amber

SIO mode - signal is high

Flashing red

Hardware fault. Ensure that configured IO-Link

settings on the port do not conflict with the

attached device. Verify that:

–

Automatic Upload and/or Download is

enabled and it is not the same device.

–

Device Validation Mode is enabled and it is

not the correct device.

–

Data Validation Mode is enabled but there

is an error.

Solid red

PDI of the attached IO-Link device is invalid.

Solid green

An IO-Link device is connected and

communicating.

Flashing green

Searching for IO-Link devices

DI (Digital Input)

Off

DI signal is low or disconnected

Solid amber

DI signal is high

Ethernet ports

Solid green

A link is established

Flashing amber

Data transfer activity

Table 6-1

LED indication

LED name

Status

Indication

Summary of Contents for IOL MA8 PN DI8





















































































Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands

Phoenix Contact IOL MA8 PN DI8, User Manual

Search results

Summary of Contents for IOL MA8 PN DI8

Reviews:

Related manuals for IOL MA8 PN DI8

Brands by name

Popular brands