manualshive.com logo in svg

Parker ACR9000, Installation Manual

Share
Download
Parker ACR9000 Installation Manual Download Page 117

 Parker 

Hannifin 

Drive I/O  

We have pre-configured the standard drive functionality used with stepper 
and servo drives. These functions will allow users to enable, reset, and 
monitor position error on each of the drive connectors. 

Basic Setup 

As in other ACR controllers, the first step is to attach the axes to the master 
trajectory generator. There are several important changes to setup: 

•

 The 

CONFIG

 command has been eliminated for the ACR90x0, as the 

hardware is not field-installable. The 

CONFIG

 command provides a 

report back, but the ACR90x0 configuration does not use it. 

•

 The 

MULT

 command is latched at +/-4. Modes 0, +/-1 and +/-2 are not 

valid. 

•

 The 

DAC GAIN

 command is inverted internally from the other ACR 

products. For the ACR90x0, a positive final output signal produces a 
positive voltage output. This does not apply to other ACR products. 

Attach Axis 

The 

ATTACH AXIS

 command is now used to configure the controller for 

servo or stepper control. Each axis can be setup as servo or stepper. Since 
each axis connector includes the analog, digital, and drive I/O, it is logical to 
attach ENC1 to DAC1 and so fourth. 

Example axis attachments 

P00>ATTACH AXIS0 STEPPER0 STEPPER0 

P00>ATTACH AXIS1 ENC1 DAC1 ENC1 

P00>ATTACH AXIS2 STEPPER2 STEPPER2 

P00>ATTACH AXIS3 ENC3 DAC3 ENC3 

The 

ATTACH

 command functions the same as other ACR controllers. 

Example attachments 

P00>ATTACH MASTER0 

P00>ATTACH SLAVE0 AXIS0 “X” 

P00>ATTACH SLAVE1 AXIS1 “Y” 

P00>ATTACH SLAVE2 AXIS2 “Z” 

P00>ATTACH SLAVE3 AXIS3 “A” 

P00>ESAVE 

Appendix D  Drive I/O   117 

www.comoso.com

Summary of Contents for ACR9000







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands