19
1
Press the hook of the filter case on the side of the pump and
take out the case.
2
Replace the filter.
Reset the filter operating time after re-
placing the filter.
How to clean the air cells
1
Remove the couplings (upper and lower) from the pump and discharge air from the air cells.
2
Remove the top cover.
3
Clean the air cells using the same method as the covers. (See page 18)
4
Dry the air cells naturally and always connect the couplings (upper and lower) to the pump properly. (See page 6)
5
Close the cover zippers properly.
CAUTION
After maintenance, check that the connector for the blowing tubes are not disconnected. Air
may not be supplied.
Note
!
z
When maintaining the air cells, do not separate each air cell from the mattress.
z
If the mattress is used for a long period of time, the urethane film of the air cells may be discolored but there
will be no problem with performance.
How to clean the pump and operation panel
1
Use soapy water (commercially available soap, such as neutral detergent diluted with water) to wipe and clean the pump and
operation panel.
2
Use disinfectant to clean and disinfect the pump and operation panel. For disinfectant, use the following chemicals and observe
the specified concentration. Also, use those disinfectants according to the handling method of each disinfectant.
z
76.9% to 81.4% Ethanol for disinfection
z
0.05% to 0.2%
Benzethonium chloride
z
70%
Isopropanol
z
0.05%
Chlorhexidine gluconate
z
0.05% to 0.2%
Benzalkonium chloride
z
0.02% to 1.0%
Sodium hypochlorite
Replacing the filter
Regularly inspect and replace the filter. For the details on the dedicated filter, contact Paramount Bed (see page 31) or your
distributor.
CAUTION
z
Regularly inspect the filter. If the filter is clogged, it
may not work properly.
z
If a filter other than specified is attached or no filter is
attached, insects or dust may enter the inside of the
pump, possibly causing malfunction. This also may
cause failure.
Take out
Pump side
Filter
Filter case
Press hook
How to clean the glide sheet and top cushion
1
Open the zippers and then remove the top cover from the bottom cover.
2
Remove the belts of the air cell from the rubber loops of the bottom cover at the head end two corners, and then remove the
belts of the air cell from the loops of the glide sheet. Remove the strings from the loops at the foot end two corners. Untie the
strings from the loops at the two corners and then remove both the glide sheet and top cushion together.
3
Use soapy water (commercially available soap, such as neutral detergent diluted with water) to soak the glide sheet and top
cushion to wash them together without separating them.
4
Rinse with water until there is no residual detergent and wring out gently without twisting. Dry completely in a shaded area.
[How to attach the glide sheet]
1
Lay the glide sheet on the air cells so that the tag is facing up.
2
Pass the belts of the air cell through the loops of the glide
sheet at the head end two corners, and then attach the rub-
ber loops of the bottom cover to the belts of the air cell.
3
Pass the strings at the foot end two corners of the glide sheet
through the loops from the outer side to the inner side of the
bottom cover and then tie securely.
Note
!
z
When attaching the glide sheet, take care that
the urethane sheet inside does not shift toward
one side.
z
Do not separate the glide sheet and top cush-
ion. If they are separated, check that the glide
sheet is not turned inside out and then insert
the top cushion. (Ensure the tag is on the outer
side of the glide sheet.)
Loops (two corners)
String
Glide sheet
Tag
Remove the belts of the
air cell from the rubber
loops of the bottom cover.
Remove the belts of the
air cell from the loops
of the glide sheet.
Rubber loop
Belt
Belt
Loop
5
MAINTENANCE AND INSPECTION
