background image

10

2. Starting use

 

„

How to start

Disconnect the power plug of the bed, then connect the bed link cable to the bed. See the procedure on pages 6 to 8.

 

„

How to shutdown

Disconnect the power plug of the bed and turn the battery off, then disconnect the bed link cable from the bed. 

 

„

Time required to complete air inflation

When you insert the power plug into an outlet or connect bed link cable to bed, the air cells will be automatically inflated with air 

after a short while. The “Preparing” indication will be lit during inflation. When air inflation completes, the “Preparing” indication 

turns off. (Time required to complete air inflation: 10 minutes)

 

„

When automatic softness control

When the user is lying in the bed, a softness (mattress internal pressure) that matches the weight, body shape, and lying po-

sition will be set automatically. The set softness is displayed for a while and then disappears. It can be displayed for a while by 

pressing the [Automatic softness control] button.

WARNING

When using automatic softness control, check that the width indicated on the quality label and 

the width setting indicated on the operation panel are the same (see page 11). If they differ, 

the body pressure may not be dispersed effectively.

Note

!

 

z

If the user leaves the bed when using automatic softness control, the softness may be automatically set to 

5. This is not a failure.

 

z

When the user is lying in bed, a softness that matches the user’s weight, body shape, and lying position will 

be set in about 5 to 15 minutes.

 

„

When manual softness control

Press the adjustment buttons to adjust the softness. To use automatic softness control, see page 11 and then switch to au-

tomatic softness control.

 

„

Fast inflation

I

nflate the mattress at high speed when power is supplied or max. inflate mode is set to ON.

*  The pump sound will be loud and the “Preparing” indication on the operation panel will be lit during fast inflation.

 

„

Functions retained after power-off

 

z

The function settings immediately before a power-off will be retained in the following cases.

•  When the power has recovered after a power failure

•  When restarted by disconnecting and reinserting the power plug or the bed link cable

 

z

The remaining time immediately before a power-off is retained for the max. inflate mode.

 

z

If “18^” was used with manual softness control, the softness setting becomes “18.”

 

„

Power failure countermeasure function

Automatically stop air discharge in the event of a power failure. Air can be held for two weeks, but this period varies depending on the 

conditions of use. However, the depressurization effect, alternating pressure function, etc. for the product do not work during a power 

failure, so be careful about the user’s condition. The small flow air cells (SF cells) maintain their expanded state. Contract them by 

disconnecting the coupling (upper) if necessary.

4

 FUNCTIONS AND OPERATING PROCEDURES

3. Setting of each function

3-1.  How to switch to the setting display

1

 Press the Setting button on the back of the operation panel.

2

 When you press the Setting button, the various setting buttons light and operation becomes possible. Unselected setting but-

tons of the various setting buttons are dimmed.

3

 

Press the Setting button on the back of the operation panel. The changes to the settings complete and the various setting buttons turn off.

Note

!

Even if you select various settings during setting display, changing of the settings will not complete if you do 

not press the Setting button on the back of the operation panel again. Check that the changes are reflected in 

the status display screen after changing settings.

1

 Press  the 

Setting button 

to switch 

to setting 

display.

2

 Press  the 

button of the 

setting you 

wish to set.

3

 Press  the 

Setting 

button to 

complete 

the setting.

Summary of Contents for cococia Riraku flow

































Reviews: