Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download

Page: 93 / 126

■

Resetting the Alarm Inputs

There are two alarm reset functions:

• Alarm reset (resetting the alarm inputs per monitor)
• Alarm all reset (resetting all the alarm inputs)

●

Alarm Reset

1. Select a monitor which displays "ALARM".
2. To reset the alarms, press the ALM RESET/ALM ALL

RESET button.
"ALARMnn" will disappear from the selected monitor.
When alarms have been reset from all the monitors, the
LCD display and indicators of system controllers will
work as follows for recovery.

• The LCD display will return to the state before the

alarm input.

• The alarm indicator will go out.

Note:

When more than one alarm is input and they are

associated with the same monitor, they cannot be reset
one by one.

●

Alarm All Reset

1. Press the ALM RESET/ALM ALL RESET button while

holding down the SHIFT button.

2. The monitor, the indicator, and the LCD display will

change as follows:

• "ALARMnn" will disappear from all the monitor.
• The LED display will return to the state before the

alarm input.

• The alarm indicator will go out.

■

Suspending the Alarm Inputs

Use this function when you do not want to be disturbed by
an alarm input, for example, during the setup procedures.

1. Press the ALARM/ALM SUSPEND button while holding

down the SHIFT button.
"ALM SUSPENDED" will appear on the monitor, and the
ALM SUSPEND indicator will light up.

2. To cancel alarm suspension, press the ALARM/ALM

SUSPEND button while holding down the SHIFT button
again.
"ALM SUSPENDED" will disappear from the monitor,
and the ALM SUSPEND indicator will go out.

Notes:

• An alarm continues to operate even after it is suspend-

ed.

• If you suspend an alarm while an alarm image is dis-

played, "ALM SUSPENDED" will not appear on the moni-
tor. Reset the alarm, and then suspend it again.

ALM SUSPENDED

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands