manualshive.com logo in svg

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Share
Download
Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download Page 51

51

1

The image of camera with the higher channel number will
be displayed.

Camera –1

The image of camera with the lower channel number will be
displayed.

HD300 A-B Repeat (WJ-HD300 Series Only)

• You will set the start and end points of A – B repeat

playback of WJ-HD300 Series.

• You will cancel A – B repeat playback of WJ-HD300

Series.

HD500 Copy (WJ-HD500 Series Only)

Recorded images will be copied from the built-in hard disk
of recorder to external recording devices.

HD200 Alarm Search (WJ-HD200 Series Only)

The alarm search function of recorder will be activated.

Multiscreen Display

The screen of monitor connected to the selected system
unit will be divided in multiscreen segments.

Note:

Available multiscreen segment patterns differ

depending on system units. Refer to the operating
instructions of system units.

■

To Recall Menu Functions

You can recall menu functions as follows.

1. Select a system unit for which you wish to recall a func-

tion. (Refer to p. 31 System Unit Selection, p. 31
Recorder Selection, p. 32 Monitor Selection, or p. 32
Camera Selection.)

Note:

You can skip Step 2 and 3 if you know what func-

tion to recall. In this case, enter a function number,
and press the MENU button. Then, go to Step 4.

2. Press the MENU button.

“Camera Setup” main menu will appear on the LCD.

3. Select a desired function.

Select a category (

q

) by rotating the shuttle ring. Then,

select a function number (

w

) by rotating the JogDial.

Note:

Refer to pp. 48 to 51 for selectable functions.

J/S MENU         510

1

LCD MENU     CAM 101

Camera Setup

LCD MENU     SYS 301

System Setup

Mon01 Cam016   HD316

  F1   F2   F3   F4

J/S MENU         511

Camera -1

J/S MENU         512

HD300 A—B Repeat

J/S MENU         513

HD500 Copy

J/S MENU         514

HD200 Alm Search

J/S MENU         515

Multi  4-Seg

J/S MENU         516

Multi  7-Seg

J/S MENU         517

Multi  9-Seg

J/S MENU         520

Multi 16-Seg

J/S MENU         519

Multi 13-Seg

J/S MENU         518

Multi 10-Seg

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands