Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download

Page: 108 / 126

WJ-HD200 SERIES CONTROL (TERMINAL MODE)

Matrix switcher can control Digital Disk Recorder WJ-
HD200 Series. The following is the procedure of WJ-HD200
Series SETUP MENU.

Notes:

• The following operating procedures are for the terminal mode.

If you are using a PS·Data system controller, refer to p. 36.

• When a Multiplexer board is installed in the matrix switch-

er, you can neither connect nor control a WJ-HD200 Series
recorder. You need to remove the board from the matrix
switcher.

■

Displaying WJ-HD200 Series
SETUP MENU

The operations are the same as WJ-HD500 Series. (Refer to
p. 18.)

■

Controlling Digital Disk
Recorder WJ-HD200 Series

The following are the operating procedures of WJ-HD200
Series via system controller.

Note:

Refer to the operating instructions of Digital Disk

Recorder WJ-HD200 Series for details.

●

Recorder Mode

The operations are the same as WJ-HD500 Series. (Refer to
p. 19.)

●

Multiscreen Segment Switching

The operations are the same as WJ-HD500 Series. (Refer to
p. 19.)

Note:

4C-, 4D-, 7-, 10-, 13- and 16-segment multiscreen

display patterns are unavailable.

●

Normal Playback

The operations are the same as WJ-HD500 Series. (Refer to
p. 19.)

Note:

You cannot skip to the previous/next record.

●

Manual Recording

The operations are the same as WJ-HD500 Series. (Refer to
p. 20.)

Note:

Refer to WJ-HD200 Series Operating Instructions for

details and other recording modes.

●

Stopping REC ONLY Alarm
Recording

The operations are the same as WJ-HD500 Series. (Refer to
p. 20.)

●

Search Playback

You can search playback images using the ALARM
RECALL table or the SEARCH table.

Every time you press the SEARCH/T&D SEARCH button,
the display will change as follows.
Live image

→

Date-and-time entry form

→

ALARM RECALL

table

→

Live image

• Date-and-time Search Playback

The recorded images can be searched for through the date
and time.

1. Enter the recorder mode. (Refer to p. 19 Recorder

Mode.)

2. Press the SEARCH/T&D SEARCH button. The date-and-

time entry form will appear on the center of the monitor.

Note:

The factory default setting is the current date and

time.

SEARCH
YYYY/MM/DD HH:MM
20

/05/07 19:32

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands