Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download

Page: 96 / 126

WJ-HD500 SERIES CONTROL (TERMINAL MODE)

Matrix switcher can control Digital Disk Recorder WJ-
HD500 Series. The following is the procedure of WJ-HD500
Series SETUP MENU.

Notes:

• The following operating procedures are for the terminal mode.

If you are using a PS·Data system controller, refer to p. 36.

• When a Multiplexer board is installed in the matrix switch-

er, you can neither connect nor control a WJ-HD500 Series
recorder. You need to remove the board from the matrix
switcher.

■

Displaying WJ-HD500 Series
SETUP MENU

To display WJ-HD500 Series SETUP MENU, follow the pro-
cedure below.

1. Confirm that WJ-HD500 Series is correctly and securely

connected.

2. Select the desired monitor. (Refer to p. 3 Monitor

Selection.)

3. Enter the recorder mode. (Refer to p. 19 Recorder

Mode.) Then, the selected monitor number, recorder
number, and "/HDnnn" will appear on the LCD.

4. Press the MENU button repeatedly until “System Setup”

appears on the LCD.

5. Press the F1 button.

WJ-HD500 Series SETUP MENU will appear on the
active monitor, and “

” mark will light up beside “On”.

6. Perform the camera setting while watching the setup

menu on the monitor.
The following functions and buttons are valid in SETUP
MENU.

<Main unit>
JogDial clockwise:

Increments a parameter.

JogDial counterclockwise:

Decrements a parameter.

CAM (SET) button:

Executes the selections and dis-

plays a submenu.

+ button:

Increments a parameter.

– button:

Decrements a parameter.

MON (ESC) button:

Returns to SETUP MENU or the

previous menu.

<3D joystick unit>
3D joystick upward (

Moves the cursor up.

3D joystick downward (

Moves the cursor down.

3D joystick leftward (

Moves the cursor to the left.

3D joystick rightward (

Moves the cursor to the

right.

6. To end the setting and return to the normal view, press

the F2 button while SETUP MENU is displayed. "

mark will disappear from the LCD.

Mon4 Cam-- R4

/HD500

System Setup 501

On Off

System Setup 501

On Off

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands