Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download

Page: 57 / 126

●

Auto Pan Setup and Activation

You will set up and activate the auto pan function. The cam-
era can pan between the start and end points you will set.

To set the start and end point of auto pan

1. Display “Auto Pan” sub menu. (Refer to Step 1 to 4 of p.

51 To Recall Menu Functions.)

2. By moving the 3D joystick, move the camera to a point

you wish to start auto pan.

3. Press the F3 button.

The start point of auto pan will be set.

4. By moving the 3D joystick, move the camera to a point

you wish to end auto pan.

5. Press the F4 button.

The end point of auto pan will be set.

To activate auto pan

Press the F1 button.
The auto pan will be activated, and the camera will pan
between the set.

Notes:

• When you press the F2 button, the auto pan direction

will be reversed.

• Auto pan will be canceled when you pan or tilt the

selected camera by moving the 3D joystick.

■

Recorder Functions

●

Disk Selection
(WJ-HD300 Series Only)

You will specify a disk for search playback.

1. Display “HD300 DiskSelect” sub menu. (Refer to Step 1

to 4 of p. 51 To Recall Menu Functions.)

2. Press one of the F1 to F4 buttons.

The specified disk will be selected.

Available buttons and functions

F1: Nr-A

Specifies the normal or event recording area for
playback.

F2: Cp-A

Specifies the copy area for playback.

F3: Cpy1

This function is reserved for future use.

F4: Cpy2

This function is reserved for future use.

3. When you specify a disk, the search list display will

appear on the active monitor, and “Search Mode” menu
will appear on the LCD. Then, perform the search play-
back operation. (Refer to p. 35 Search Playback.)

●

A-B Repeat Playback Setting
(WJ-HD300 Series Only)

You can playback the recorded images repeatedly by
specifying the start point (A) and end point (B).

1. Display “HD300 A- B Repeat” sub menu. (Refer to Step

1 to 4 of p. 51 To Recall Menu Functions.)

2. During playback, press the F1 button at the point you

wish to start playback. The playback start point (A) will
be set.

Note:

To cancel the start point, press the F4 button.

3. Press the F2 button at the point you wish to end play-

back. The playback end point (B) will be set, and the
repeat playback will be performed between (A) and (B).

HD300 A—B Repeat 202

Start End Cancel

Auto Pan Setup 105

Play Rvrs Start End

Search Mode HD300

Thumb Text Copy

HD300 DiskSelect 201

Nr-A Cp-A Cpy1 Cpy2

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands