Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Operating Instructions Manual Download

Page: 85 / 126

■

Patrol Learn and Play

A routine of manual operations can be stored for a specific
time and later reproduced repetitively.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. To save the patrol sequence, follow the procedure

below.

Press the MENU button repeatedly until "Patrol
Learn" will appear on the LCD.

Press the F1 button.

Operate the camera manually.

Press the F2 button.
The operation data will be saved.

3. To reproduce the operation data, follow the procedure

below.

Press the MENU button repeatedly until "Auto
Mode" appears on the LCD.

Press the F4 button.

To stop the reproduction, move the 3D joystick.

4. To exit the mode, press the MON (ESC) button.

Patrol Learn 007

Start Stop

Auto Mode 009

Seq Sort Pan Patrol

■

Auto Pan Setup and Activation

You will set up and activate the auto pan function. The cam-
era can pan between the start and end points you will set.

1. Select the desired monitor and camera. (Refer to p. 3

Monitor Selection and p. 3 Camera Selection.)

2. Press the MENU button repeatedly until "Auto Pan

Setup" appears on the LCD.

3. To set the start and end point of auto pan, perform the

following.

To move the camera to a point you wish to start
auto pan, move the 3D joystick and press the lens
control buttons (IRIS OPEN and CLOSE, FOCUS
FAR and NEAR).

Press the F3 button.
The start point of auto pan will be set.

To move the camera to a point you wish to end auto
pan, move the 3D joystick.

Press the F4 button.
The end point of auto pan will be set.

Auto Pan Setup 008

Play Rvrs Start End

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM































































































































Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM, Operating Instructions Manual

Search results

Summary of Contents for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Reviews:

Related manuals for WVCU650 - SYSTEM CONTROLLER ADDENDUM

Brands by name

Popular brands