[PROJECTOR SETUP] menu
ENGLISH - 69
Settings
[SCHEDULE]
Set the command execution schedule for each day of
the week.
1) Press
▲▼
to select [SCHEDULE].
2) Press
◀▶
to switch [SCHEDULE].
▶
z
The setting will change as follows each time
you press the button.
[ON]
[OFF]
Note
z
When [SCHEDULE] is set to [ON], the [STANDBY
MODE] setting is forcibly switched to [NORMAL],
and the setting cannot be changed. Even if
[SCHEDULE] is then set to [OFF] when in this
state, the setting of [STANDBY MODE] remains at
[NORMAL].
▶
■
How to assign a program
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z
The
[SCHEDULE]
screen is displayed.
4) Select and assign program to each day
of week.
▶
z
Press
▲▼
to select the day of week, and press
◀▶
to select a program number.
▶
z
You can set the program from No.1 to No.7. “-
- -” indicates that the program number has not
been set yet.
▶
■
How to set a program
You can set up to 16 commands to each program.
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z
The
[SCHEDULE]
screen is displayed.
4) Press
▲▼
to select [PROGRAM EDIT].
5) Press
◀▶
to select a program number
and then press the <ENTER> button.
6) Press
▲▼
to select a command
number and press the <ENTER>
button.
▶
z
You can change the page using
◀▶
.
7) Press
▲▼
to select [TIME], and press
the <ENTER> button.
8) Press
◀▶
to select hour and minute,
and press
▲▼
or the number (<0> to
<9>) buttons on the remote control
to set a time, and press the <ENTER>
button.
9) Press
▲▼
to select [COMMAND].
10) Press
◀▶
to switch [COMMAND].
▶
z
The setting will change as follows each time
you press the button.
[POWER ON]
[STANDBY]
[SHUTTER]
*1
[SIDE BY SIDE]
*1
[INPUT]
*1
[LAMP POWER]
*1
[LAMP SELECT]
*1
*1: Displays the details set in Step 10).
11) Press the <ENTER> button.
▶
z
The
[COMMAND]
detailed screen is displayed.
12) Press
▲▼
to select a command.
▶
z
For [SHUTTER], [INPUT], [LAMP SELECT],
[LAMP POWER], and [SIDE BY SIDE], the
setting will change as follows each time you
press
◀▶
.
▶
z
[SHUTTER]
[OPEN]
[CLOSE]
▶
z
[INPUT]
[RGB1]
[RGB2]
[VIDEO]
[HDMI]
[DVI-D]
[S-VIDEO]
▶
z
[LAMP SELECT]
[DUAL]
[SINGLE]
▶
z
[LAMP POWER]
[NORMAL]
[ECO]
▶
z
[SIDE BY SIDE]
[ON]
[OFF]
13) Press the <ENTER> button.
▶
z
The command is fixed and ● is displayed at the
left of the selected command.
▶
z
After the command is fixed, press the <MENU>
button to close the detailed setting menu.
14) Press
▲▼
to select [STORE], and
press the <ENTER> button.
Note
z
If you try to register a setting that would cause the
lamp to flash for a short time, an error message
will be displayed on the screen. Set the time and
command again.
