Panasonic KX-TS600FX Operating Instructions Manual Download Page 46

Page: 46 / 48

Troubleshooting

You cannot store a name
and phone number in
memory.

• Programming is not possible when the

handset is off the cradle or the
SP-PHONE/HEADSET indicator lights.

• Check that the batteries are installed in

the unit and that the battery power is not
low.

• Do not pause for over 60 seconds while

storing.

• Do not enter a phone number more than

32 digits long.

• When using the Dial Lock (p. 39) or Call

Restriction feature (p. 40), you cannot
store a phone number in the Direct Dial
memory (

[M1]

[M2]

and

[M3]

) and

emergency numbers (#).

• If “

Phonebook full

” is displayed,

erase other stored items from the
Phonebook memory (p. 31).

While programming or
searching, the unit starts to
ring and stops the program/
search.

• To answer the call, lift the handset or

press

[SP-PHONE/HEADSET]

. Start

again from the beginning after hanging
up.

The display exits the Caller
List.

• Do not pause for over 60 seconds while

searching.

You cannot redial by
pressing

[REDIAL]

• If the last number dialled was more than

32 digits long, the number will not be
redialled correctly.

Information stored in the
Redial List is erased.

• If “

” flashes, replace the batteries as

soon as possible. Otherwise,
information stored in the Redial List may
be erased, and beep may not sound.
Store the desired item in the Phonebook
or Direct Dial memory, if necessary.

Problem

Cause and Remedy

TS600FX.book Page 46 Wednesday, April 5, 2006 10:27 AM

Summary of Contents for KX-TS600FX

















































Search results

Summary of Contents for KX-TS600FX

Reviews:

Related manuals for KX-TS600FX

Brands by name

Popular brands

Panasonic KX-TS600FX, Operating Instructions Manual

Search results

Summary of Contents for KX-TS600FX

Reviews:

Related manuals for KX-TS600FX

Brands by name

Popular brands