Panasonic KX-TS600FX Operating Instructions Manual Download Page 44 | Manualshive

Page: 44 / 48

background image

44

If “

” flashes, the battery power is low. Install new batteries as soon as

possible. If batteries are not replaced even after the “

” is displayed, the

unit may not work properly.

• Store the desired items in the Phonebook or Direct Dial memory, because after

the battery replacement, the information stored in the Redial List will be cleared.

1

Disconnect the telephone line
cord from the unit.

2

Press down in the direction of the
arrow and open the cover (

1

).

3

Replace the batteries with new
ones matching the correct polarity
(+, –) (

2

), and close the cover.

4

Connect the telephone line cord
to the unit.

• The time will be shown as “

0:00 31.12

” or “

12:00AM 31.12

” and “

” will

flash after replacing the batteries. Readjust the time and date.

Battery Precautions:

The batteries should be used correctly, otherwise the unit may be damaged by
battery leakage.
— Do not mix different types of batteries.
— Do not charge, short-circuit, disassemble, heat or dispose the batteries in fire.
— Remove all the batteries when replacing.

Note:

— If you do not install the batteries or if the battery power is low, the time will be

shown as “

0:00 31.12

” or “

12:00AM 31.12

” and “

” will flash. Readjust

the time after the battery replacement.

— Replace all the batteries every six months if using Alkaline batteries, or

misoperation may occur. (When you use Manganese batteries, replace all of
them every three months.)

— Do not use nickel-cadmium batteries.

Battery Replacement

TS600FX.book Page 44 Wednesday, April 5, 2006 10:27 AM

«
...
42
43
44
45
46
...
»

Summary of Contents for KX-TS600FX

















































Reviews:

No comments

Related manuals for KX-TS600FX

Brand: Panasonic Pages: 268

Brand: TCL Pages: 21

Sailor System 5000 MF/HF

Brand: Sailor Pages: 56

Brand: Q-Light Pages: 2

Brand: Talkaphone Pages: 6

Brand: BRONDI Pages: 80

Brand: GE Pages: 2

SPP-A2780 - 2.4ghz Cordless Telephone

Brand: Sony Pages: 2

SPP-A2770 - 2.4ghz Cordless Telephone

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

SPP-900 - Cordless 900mhz Telephone

Brand: Sony Pages: 28

Brand: Sony Pages: 24

Brand: Sony Pages: 38

SPP-935 - 900 Mhz Cordless Phone

Brand: Sony Pages: 43

Brand: Sony Pages: 40

Brand: Sony Pages: 34

SPP-A400 - Cordless Telephone With Answering Machine

Brand: Sony Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands