Panasonic KX-TS600FX Operating Instructions Manual Download Page 47 | Manualshive

Page: 47 / 48

background image

47

Useful Inf

o

rmation

Take special care to follow the safety suggestions listed below.

Installations
Environment

1) Do not use this unit near water—for example, near a bathtub, washbowl, sink,

etc. Damp basements should also be avoided.

2) The unit should be kept away from heat sources such as radiators, kitchen

range, etc. It also should not be placed in rooms where the temperature is less
than 5 °C or greater than 40 °C.

Placement

1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not spilled

into the unit. Do not subject this unit to excessive smoke, dust, mechanical
vibration or shock.

3) Place the unit on a flat surface.

CAUTION:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. It (they) may explode.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and

may cause burns or injury to the eyes or skin. The electrolyte may be toxic if
swallowed.

4. Exercise care in handling the battery(ies) in order not to short the battery(ies)

to conductive materials such as rings, bracelets, and keys. The battery(ies)
and/or conductor may overheat and cause burns.

5. Do not recharge the battery(ies) provided with or identified for use with this

product. The battery(ies) may leak corrosive electrolyte or explode.

6. Do not attempt to rejuvenate the battery(ies) provided with or identified for use

with this product by heating. Sudden release of battery electrolyte may occur
causing burns or irritation to the eyes or skin.

7. Replace all batteries at the same time. Mixing fresh and discharged batteries

could increase internal cell pressure and rupture the discharged batteries.
(Applies to products employing more than one separately replaceable primary
battery.)

8. When installing batteries observe the proper polarity or direction. Incorrect

installation can cause charging, and may result in leakage or explosion.
(Applies to products employing more than one separately replaceable primary
battery.)

9. Remove the battery(ies) from this product if the product will not be used for a

long period of time (several months or more). During this time the battery(ies)
could leak in the product.

10. Discard the dead battery(ies) as soon as possible. The dead battery(ies) may

leak in the product.

11. Do not store this product, or the battery(ies) provided with or identified for use

with this product, in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be
protected from condensation during storage and defrosting. Batteries should
be stabilized at room temperature prior to use after cold storage.

Safety Instructions

TS600FX.book Page 47 Wednesday, April 5, 2006 10:27 AM

«
...
45
46
47
48
»

Summary of Contents for KX-TS600FX

















































Reviews:

No comments

Related manuals for KX-TS600FX

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 87

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 214

Brand: Panasonic Pages: 126

Brand: Skil Pages: 11

Berkshire 400 Plus

Brand: ATL Product Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands