Panasonic KX-TCD715EM Operating Instructions Manual Download Page 76

Page: 76 / 80

Before Requesting Help

Problem

The paged handset does not answer.

While using the intercom, two tones
sound.

The unit misdials when connected to a
PBX.

You cannot register the handset in the
base unit.

The battery strength is not displayed
correctly.

“

” flashes or the unit beeps every

15 seconds.

You charged the batteries fully, but
“

” flashes.

Remedy

•

The handset is not in the same radio area.

•

The handset is engaged in an outside call.

•

The handset has been cancelled or has not been

registered. Register the handset in the base unit
(p. 59).

•

A call is being received. To answer, press

and

or and

•

Check the pause function (p. 43).

•

The base unit has registered a maximum of 6
handsets or the handset has registered a maximum
of 4 base units.

•

A wrong base unit PIN was entered. Enter the
correct PIN.

•

There is interference from other electrical units.
Locate the handset and base unit away from them.

•

You must finish registration within 1 minute after the
ringer tone sounds, or programming will be cancelled
(p. 59).

•

Check that the battery type selection is correct
(p. 70).

•

Charge the batteries fully (p. 12).

•

Clean the charge contacts and charge again (p. 13).

•

Install new batteries (p. 70).

KX-TCD715EM-9Useful-OPT 01.7.19 2:23 PM Page 76

Summary of Contents for KX-TCD715EM

















































































Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands

Panasonic KX-TCD715EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands