Panasonic KX-TCD715EM Operating Instructions Manual Download Page 74

Page: 74 / 80

Before Requesting Help

Remedy

•

Turn the power ON (p. 13).

•

Check the settings (p. 11–20).

•

Charge the batteries fully (p. 12).

•

Clean the charge contacts and charge again (p. 12).

•

Unplug the AC adaptor and turn the power OFF to

reset. Plug in the AC adaptor and turn the power ON.
Then try again.

•

The handset has been canceled or has not been

registered. Register the handset (p. 59).

•

Re-install the handset batteries and try again.

•

You are too far from the base unit. Move closer and

try again.

•

Plug in the AC adaptor.

•

Another handset is in use or the base unit

speakerphone is in use.

•

The unit is in call prohibition mode. Cancel the mode

(p. 47).

•

The dialled number is restricted. Cancel the number

(p. 49).

•

Key lock mode is set. Cancel the mode (p. 44).

•

The handset is out of range. Move closer to the base

unit and make the call again.

•

Plug in the AC adaptor.

•

Locate the handset and base unit away from other
electrical appliances (p. 5).

•

Move closer to the base unit.

Problem

The unit does not work.

“

” flashes and an alarm tone sounds

when you press

A busy tone sounds when you
press or .

You cannot dial.

“

” flashes during a conversation and

the call is disconnected.

Static, sound cuts in/out, fades.
Interference from other electrical units.

KX-TCD715EM-9Useful-OPT 01.7.19 2:23 PM Page 74

Summary of Contents for KX-TCD715EM

















































































Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands

Panasonic KX-TCD715EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands