Panasonic KX-TCD715EM Operating Instructions Manual Download Page 21

Page: 21 / 80

Chapter 2

Basic Operations

0 0 - 0 0 - 0 0

To dial after confirming the
entered number

Enter a phone number.

•

The entered number is displayed.

•

If you misdial, press

. Digits are erased

from the right.

•

To cancel, press and hold

or press

Press .

•

“

” is displayed.

•

After a few seconds, the display will start
showing the length of the call.

To hang up, press

or place the

handset on the base unit.

•

The handset will return to the standby
mode.

Making Calls

Press .

•

“

” is displayed.

Dial a phone number.

•

The dialled number is displayed.

•

After a few seconds, the display will show
the length of the call.

•

If “ ” flashes and an alarm tone sounds
after pressing

, move closer to

the base unit. Then try again.

•

You can choose whether to display either the
length of the call or phone number in the talk
mode by programming (p. 51).

To hang up, press

or place the

handset on the base unit.

•

The handset will return to the standby
mode.

1 2 3 4 5 6 7 8

To have a hands-free phone
conversation (Using Digital
Speakerphone)

Press .

•

The button lights.

Dial a phone number.

•

The dialled number is displayed.

•

After a few seconds, the display will show
the length of the call.

When the other party answers, talk into
the microphone.

To hang up, press

or place the

handset on the base unit.

Hands-free Digital Speakerphone

For best performance, please note the
following:

•

Talk alternately with the caller in a quiet
room.

•

If the other party has difficulty hearing you,
press

to decrease the speaker

volume.

•

If the other party’s voice from the speaker
cuts in/out during a conversation, press

to decrease the speaker volume.

•

While talking, you can switch to the hands-
free phone conversation by pressing

. To switch back to the receiver,

press or .

With the Handset

Make sure that the power is ON (p. 13).

KX-TCD715EM-3Basic1 01.7.19 2:13 PM Page 21

Summary of Contents for KX-TCD715EM

















































































Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands

Panasonic KX-TCD715EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD715EM

Reviews:

Related manuals for KX-TCD715EM

Brands by name

Popular brands