Panasonic KX-TCD715EM Operating Instructions Manual Download | Manualshive

Page: 77 / 80

background image

Take special care to follow the safety suggestions listed below.

Safety

1) The unit should be connected to a power supply only of the type described in the operating

instructions or as marked on the unit.

2) When the unit is not used, turn the power off. When left unused for a long period of time, the base

unit should be unplugged from the household AC outlet.

Installations
Environment

1) Do not use this unit near water—for example, near a bath tub, washbowl, sink, etc. Damp

basements should also be avoided.

2) The unit should be kept away from heat sources such as radiators, kitchen range, etc. It also

should not be placed in rooms where the temperature is less than 5°C or greater than 40°C.

3) The AC adaptor is used as the main disconnect device, ensure that the AC outlet is located/

installed near the unit and is easily accessible.

Placement

1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto and liquids are not spilled into the unit. Do not

subject this unit to excessive smoke, dust, mechanical vibration, or shock.

3) Place the unit on a flat surface.

For best performance

1) If noise prevents the conversation from being understood at the handset, approach the base unit to

lessen the noise.

2) The handset should be used at the HIGH volume setting when the reception tone is difficult to hear

the other party.

3) The handset should be fully recharged on the base unit when “

” on the display flashes.

4) The handset aerial should not be touched during use because of its high sensitivity.
5) The maximum calling distance may be shortened when the unit is used in the following places:

Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc.

Lightning surge

This unit has already been equipped with a built-in lightning protection circuit. However, we
recommend that you install the following options, if your area has frequent lightning strikes.
1) Lightning protection on the telephone line
2) Lightning protection on the power source
To install the above options, please contact your local sales shop.

•

Lightning damage is not covered in the warranty even if lightning protection is installed.

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.

77

Safety Instructions

Useful Information

Chapter 5

KX-TCD715EM-9Useful-OPT 01.7.19 2:23 PM Page 77

«
...
75
76
77
78
79
...
»

Summary of Contents for KX-TCD715EM

















































































Reviews:

No comments

Related manuals for KX-TCD715EM

Brand: Jabra Pages: 16

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 372

JABRA FREEWAY HFS100

Brand: Jabra Pages: 40

Brand: Jabra Pages: 3

Brand: Safeline Pages: 20

Brand: Xblue Networks Pages: 52

Brand: Garmin Pages: 60

TRU341 - TRU 341 Cordless Phone

Brand: Uniden Pages: 20

Brand: Agent Headsets Pages: 1

Brand: Uniden Pages: 36

Brand: Topcom Pages: 296

Brand: Uniden Pages: 32

Brand: Panasonic Pages: 152

DSX CORDLESS LITE II

Brand: NEC Pages: 82

Brand: NEC Pages: 74

Brand: NEC Pages: 59

Brand: NEC Pages: 106

Dterm Cordless Lite

Brand: NEC Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands