Panasonic KX-NS1000 Feature Manual Download Page 223

Page: 223 / 482

Light Pattern of the Line Status Buttons

Incoming Call

Distribution

(ICD) Group

Line Status

Intercom

Line Status

CO Line Status

Line Status

Button:

Red on

Off

Green on

Light

Pattern

Slow green
flashing

Moderate
green
flashing

Rapid green
flashing

Slow red
flashing

S-CO

G-CO

L-CO

INTERCOM

ICD Group

Idle

This extension is using the line.

This extension is holding the line.

This extension is holding the line using Exclusive Hold
or using the line for an Unattended Conference.

Incoming
call/Privacy
Release

Incoming
call for
another
extension/
Another
extension
is using the
line/Another
extension
has the line
on Exclusive
Hold.

Other
extensions
are using
all CO lines
in the trunk
group.

Another
extension
is holding
the line.

Incoming call

–

This extension
is logged out
of the ICD
group.

Rapid red
flashing

Incoming call to the ICD group in Ring
distribution method

–

For information on the light patterns of PDN and SDN buttons, refer to 15.1.4 PDN (Primary Directory
Number)/SDN (Secondary Directory Number) Extension.

Light Pattern of the Corresponding Extension Status Button

DSS

Corresponding

Extension

Status Button

Red on

Off

Light Pattern

Rapid red flashing

Idle

Busy/Incoming call

/DND for CO line calls

Incoming call

Only when Call Pickup by a DSS button is disabled.

Only when Call Pickup by a DSS button is enabled.

Document Version 2016-03

Feature Manual

223

12.1.1 LED Indication

Summary of Contents for KX-NS1000



































































































































































































































































































































































































































































































Search results

Summary of Contents for KX-NS1000

Reviews:

Related manuals for KX-NS1000

Brands by name

Popular brands

Panasonic KX-NS1000, Feature Manual

Search results

Summary of Contents for KX-NS1000

Reviews:

Related manuals for KX-NS1000

Brands by name

Popular brands