Panasonic FP-7818 Service Manual & Parts Manual Download

Page: 356 / 402

6-16

Location

Procedure

Check

Install the sorter mounting bracket to

the sorter.

(4 shoulder screws, M4 X 12)

Pull out the rail assembly fully, and

install the sorter.

Note: Hold the sorter with both hands

as shown in the figure.

If holding the other parts, sorter

will be damaged.

Fix the rail assembly (front/rear side).

(2 screws, M4 X 8)

Sorter mounting bracket

(Rear side)

(Front side)

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands