Panasonic FP-7818 Service Manual & Parts Manual Download

Page: 357 / 402

Unpacking/

Installation

6-17

Location

Procedure

Check

Connect the lattice connector of the

sorter to the copier.

Attach the "Staple" label.
(1) Open the platen cover (or ADF).
(2) Attach "Staple" label (A) provided

on the upper cover (rear).

(When the ADF is installed)
<FA-A888>
Attach "Staple" label (B) provided on
the main cover.

Operation check
(1) Place some paper in the stapler

position on the top bin and press
the manual staple key.

(2) Remove the paper from the bin

and check staple.

(3) When sheets of paper are not

stapled, repeat steps (1) - (2).

(Copier upper rear cover)

<FA-A888>

Staple label (A)

Staple label (B)

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands