Panasonic FP-7818 Service Manual & Parts Manual Download

Page: 355 / 402

Unpacking/

Installation

6-15

Location

Procedure

Check

(1) Remove 2screws of the rear

cover (copier and system con-

sole).

(2) Install the connecting plate to the

rear cover (copier and system

console).

(2 screws, just removed)

Install the floor stabilizer to the system

console.

(2 screws, M4 X 14)

Note: Put the floor stabilizer com-

pletely on the flower.

Insert the rail assembly into the lower

slits of copier left cover, then fix the

rail assembly. (2 screws, M4 X 33)

Connecting plate

fall stabilizer

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands