Panasonic FP-7818 Page 308 Service Manual & Parts Manual Download

Page: 308 / 402

3-2

3.2 Disassembly/Assembly

(1) Replacement of the stapler assembly (FA-S620)

Remove the front cover, right cover, and rear

cover.

Remove the tie-wrap.

Disconnect the connector.

Remove the ground wire. (1 screw)

Rotate the stapler swing motor to move

the stapler unit to the position indicated

in the diagram.

Remove the stapler unit. (2 screws)

Front cover

Rear cover

Right cover

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands