manualshive.com logo in svg

Panasonic FP-7818, Service Manual & Parts Manual

Share
Download
Panasonic FP-7818 Service Manual & Parts Manual Download Page 353

Unpacking/

Installation

6-13

Location

Procedure

Check

5

(1) Pull out the lower cassette.

(2) Remove the rail stopper. (1 screw)

(3) Remove the lower cassette.

6

(1) Remove the lower cassette rail

fixing screw. (front side X 1)

(2) Install the sorter receiving bracket

(front), together with the lower

cassette rail. (2 screws just re-

moved)

7

Re-install the lower cassette and rail

stopper.

9

Remove the system console left

cover. (2 screws)

1

3

2

Rail stopper

1

2

Sorter receiving bracket (front)

8

(1) Re-install the left cover and rear

cover.

(2) Close the exit door and front door.

Summary of Contents for FP-7818



















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands