Panasonic FP-7818 Service Manual & Parts Manual Download

Page: 312 / 402

3-6

(4) Replacement of the bin unit (FA-S660)

Remove the front cover, right cover, and rear

cover.

Disconnect the connector of the sorter

controller PCB. ( x 4)

Detach the signal code plate. (2 screws)

Remove two screws (front/rear).

Lift the guide rail hitch.

Place the detached bin unit as shown.

Replacing the bin from the upper side

(See 8 for replacing the bin from the lower

side)

Place the bin unit sideways on the work

table.

Remove the slide rails (front/rear). (2

screws)

Remove the bin front cover and bin rear

cover.

(front side: 3 screws, rear side: 4 screws)

Signal code plate

Slide rail

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands