Panasonic FP-7818 Page 33 Service Manual & Parts Manual Download

Page: 33 / 402

2-8

2. 5 Re-try Control for Paper Misfeed

• Copy paper should pass the paper feed sensor within a specific time after the

paper feed clutch turns on. To reduce paper misfeeds due to a slipping paper

feed roller, the paper feed clutch turns on again (re-try operation).

• When the paper does not reach the paper feed sensor within a specific time after

two re-try operations, "jam" is indicated.

The re-try control for misfeeds is executed for each paper feed unit.

Motor off

Re-try

925ms. 500ms.

2038ms.

ON
OFF

H
L

Paper feed motor

Paper feed clutch

Paper feed sensor

Summary of Contents for FP-7818



















































































































































































































































































































































































































Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands

Panasonic FP-7818, Service Manual & Parts Manual

Search results

Summary of Contents for FP-7818

Reviews:

Related manuals for FP-7818

Brands by name

Popular brands