004778250 - 30/03/2020
63
FRANÇAIS
5. FONCTIONNEMENT
5.1 MARCHE/ARRÊT
La marche/arrêt de la centrale se fait en appuyant de façon prolongée sur la touche
K1
L’état ÉTEINT est signalé par la touche
K1
allumée
Quand on démarre la centrale, la séquence suivante de messages s’affiche :
o
Code Produit
t013
o
Révision produit
r 0.1
o
rc0.1
o
Configuration
CF17
5.2 AFFICHAGE SONDES
L’afficheur visualise la valeur courant lue par la sonde
S1
(la LED
S1
est allumée).
En appuyant sur
K4
ou
K3
, on accède au menu sondes et la température de la sonde
S2
s’affiche (la LED
S2
clignote) ou de la
sonde
S3
(la LED
S3
clignote)
La pression de la touche
K3
ou
K4
permet de faire défiler les autres sondes (si présentes).
Pour quitter le Menu, appuyer sur la touche
K1
ou attendre 10 secondes.
Si la lecture des Sondes est plus basse que la plage minimum du capteur, le message
Lo
s’affiche
Si la lecture des Sondes est plus élevée que la plage maximum du capteur,
le message
Hi
s’affiche
5.3 FONCTION SÉCURITÉ
Cette fonction, si activée P11=1, permet de lancer la procédure d’élimination de la chaleur en excès de l’insert
La gestion de la fonction Sécurité est décrite à l’intérieur des paragraphes relatifs aux schémas Installation.
5.4 FONCTION ALARME
Si la température lue par la
Sonde S1
dépasse la valeur du Thermostat d’Alarme
A08
le signal sonore et visuel se déclenche (la température clignote sur l’afficheur)
Fonction
SILENCE
: le
signal sonore peut être désactivé pendant 5 minutes en appuyant sur une touche quelconque.
Si la condition d’alarme persiste, le signal sonore est réactivé.
5.5 FONCTION ANTIGEL
Si la température lue par la
Sonde S1
descend sous la valeur du Thermostat Antigel
A06
la sortie Pompe
P1
est activée pendant le temps
t01
à des intervalles de temps
t02
L’afficheur visualise le message
ICE
5.6 FONCTION ANTI-BLOCAGE POMPE P1
En cas d’inactivité de la Pompe
P1
, même en état ÉTEINT, pendant un temps supérieur au Temporisateur
t05
la sortie Pompe
P1
est activée pendant
t04
secondes
L’afficheur visualise le message
bLP
5.7 FONCTION STANDBY
En cas de dispositif
ÉTEINT
,
en condition
ALARME
,
ANTIGEL
ou
ANTI-BLOCAGE Pompe P1
le dispositif se place automatiquement en état
ALLUMÉ
Lorsque les conditions de
ANTIGEL
ou
ANTI-BLOCAGE Pompe
terminent, la centrale revient sur l’état ÉTEINT.
Lorsque la condition
ALARME
termine, la centrale demeure sur l’état ALLUMÉ.
5.8 FONCTION TEST POMPE P1
En état ÉTEINT, en appuyant de façon prolongée sur la touche
K3
la sortie
P1
est activée pendant toute la durée de la pression de la touche et l’afficheur visualise
tSt1
5.9 FONCTION TEST POMPE P2
En état ÉTEINT, en appuyant de façon prolongée sur la touche
K4
la sortie
P2/P4
est activée pendant toute la durée de la pression de la touche et l’afficheur visualise
tSt2
5.10 SORTIE SERVICE
La sortie P4 SERVICE est programmable dans le MENU Installateur à travers le paramètre
P06
:
P06 = 0 EXCLUE
: la sortie ne fonctionne pas
P06 = 1 THERMOSTAT
: la sortie est activée si la température de la Sonde
S1
est supérieure à la valeur du Thermostat
A09
P06 = 2 GRILL
: en appuyant sur la touche
K1
on peut allumer/éteindre la sortie
P06 = 3 REGISTRE AIR
: la sortie gère un registre pour le réglage de l’air de combustion
5.11 REGISTRE AIR
Le Registre Air est validé pour son fonctionnement si le paramètre
P06 = 3
Si la Sortie est active (ON) le Registre est Ouvert, si la Sortie est éteinte (OFF), le Registre est Fermé.
Le Registre est Ouvert tant que la température de la sonde S1 est inférieure à la valeur du Thermostat
A05
. Il se ferme dès que la
température dépasse cette valeur du Thermostat
.
Se
P12 = 1
la fonction
Start Manuel
est validée :
Si la Température de S1 est inférieur à
A01
, le Registre se referme. En phase d’Allumage de l’Insert, à travers la pression de la touche
K1
, on force l’ouverture manuelle du Registre (la LED correspondant à la sortie clignote). Lorsque la température descend de nouveau
sous la valeur du thermostat
A01
, une fois le temps
t06
écoulé, le registre se referme automatiquement.
4