26
27
Causes
Solutions
Display
System overheated
Turn off the coffee machine and
turn it on after an hour.
Operating temperature of the coffee machine
in the room is below 10° C
Move the coffee machine into a
warm room
Making beverages is not available
Power off, restarting up. If still
unresolved, please pull out the
plug. Contact with Oursson
customer service center.
Pressure is too high when making coffee
Clean the brewing unit
Making beverages is not available
Turn off the coffee machine and
turn it on again.
Problem with brewing unit. Making beverages
is not available
Turn off the coffee machine and
turn it on again.
Problem
Cause
Solutions
The coffee temperature is
too low
The coffee cup was not pre-heated
Wash the coffee cup with hot water
before making coffee.
Several minutes have passed since
the last time of coffee making, so the
brewing unit and the internal pipes are
already cold.
To make many cups of coffee.
Coffee only comes out
from the coffee spout drop
by drop
The Coffee bean powder is too fine, or it
has been ground too fine.
Adjust the grinding wheel to a rough
state or use the suitable coffee
powder to make espresso.
Brewing unit filter was blocked.
Run the brewing unit washing
program.
The grinder arising noises
There are foreign objects in the grinder.
Make coffee again, if it still failures,
please contact with the Oursson
customer service center.
The milk frother cannot
make any milk foam
The milk frother is blocked.
Clean the milk frother.
Milk sprays from the milk
frother
The milk frother was not assembled
correctly.
Reassemble the milk frother.
Screen always indicates
«EMPTY TRAY»
The sheet metals at ends of the drip tray
are dirty or wet.
Clean the sheet metals according to
CLEANING AND MAINTENANCE.
ERROR 1
TEMPERATURE HIGH
PRESSURE HIGH
VALVE RESET
RESTART MACHINE
BREW UNIT RESET
RESTART MACHINE
TEMPERATURE LOW
For information on product certification, see
http://www.oursson.com/rus/ru/about/partners/certificates/#tab0
or ask seller
for a copy.
PRODUCT CERTIFICATION
*
Products should be stored in dry, ventilated warehouses at temperatures below
- 25°С.
Reparation must be performed only by a qualified personnel authorized by OURSSON AG service
center.
Problem
Cause
Solutions
Screen always indicates
«INSTALL GOUNDS
CONTAINER»
Coffee grounds in the bottom of the
machine are not cleaned.
Clean the coffee grounds according to
CLEANING AND MAINTENANCE.
Screen always indicates
«FILL WATER TANK»
The water tank inductor is trapped.
Clean the water tank according to
CLEANING AND MAINTENANCE.
•
Please save the packaging of the coffee machine for
future transportations.
•
Make sure to empty water inside the machine before
transportation, otherwise, it will damage the machine.
•
After emptying the waterway, please wipe dry the
machine both inside and outside.
•
Once the empty waterway program was
executed, the system will rerun to the program
of «first-time use», when the coffee machine is
used again, you must complete all steps from the
FIRST-TIME USE.
•
Display «
READY
»
•
Remove the water tank from the coffee machine.
TRANSPORTATION
Display «
FILL WATER TANK
»
•
Press and hold for 2 seconds, display will say
«
EMPTY UNIT
».
•
Steam and water will come out from the spouts.
•
After the water is drained, the coffee machine will
turn off.
1
2
3
4
Specifications
Model
AM6244
Power consumption, W
max 1200
Rated voltage
220-240 V~; 50 Hz
Coffee mill power, W
20
Pump pressure, bar
19
Water tank volume, L
1.8
Beans tank capacity, g
250
Thick tank volume
15 cups
Brew block volume, g
7 - 14
Adjustment height of coffee spout
from 80 up to 140 mm
Power cord length, m
1.2
Temperature:
Operating
+15°C to +35°C
Storage and transportation
- 25°C to +55°C
Humidity:
Operating
15-75%
Storage and transportation
15-75%
Level of protection
I
Dimensions, mm
450×302×370
Weight, kg
13
READY
FILL WATER TANK
EMPTY UNIT
